GALAKSIJA PLUS
GALAKSIJA PLUS / ГАЛАКСИЯ ПЛЮС
Galaksija Plus was an improved version of Galaksija, with 256 X 208 monochrome graphics mode, 3 - voice sound based on AY-3-8910 and 48 KB RAM.
The hardware of Galaksija Plus was created by Nenad Dunyich and software by Milan Tadich in 1985. The goal was to enhance original Galaksija while keeping the original goal of keeping things inexpensive and simple for the constructor.
Continuing to use Static RAM in Galaksija Plus would have significantly increased the cost, so designers decided to switch to dynamic, built out of 4416 chips. Larger memory prompted the need for faster cassette tape data recording rate, which was increased to 1200 bit / s by modifying another piece of firmware.
Having enough memory to store the bit map and since Galaksija's own CPU directly drove the video signal, video generation hardware did not have to change significantly. Video generation routine was modified to take the raw video data from the new video memory instead of relying on character set ROMs. Some games for original Galaksija used to do a similar trick, albeit in a limited fashion due to restrictive memory capacity.
The final hardware upgrade was addition of AY-3-8910 sound - generation chip, providing contemporary - standard sound to Galaksija without the need to use tricks such as with the cassette tape port.
Galaksija Plus featured new software additions: Graphic primitives in BASIC language - commands to draw lines, boxes, circles, other graphic primitives as well as drawing text on graphical screen with different font. Additional firmware (ROM C) also featured Full Screen Source Editor and soft scrolling.
SPECIFICATIONS
- ROM: additional ROM "C" or "3" - 2 KB (in 2716 EPROM) - additional firmware specific to Galaksija Plus (e.g. graphics mode drivers and handling);
- RAM: 48 KB of 4416 dynamic RAM, 46 KB accessible;
- Storage media: cassette tape, recording at either 280 or 1200 bit / s rate;
- Text mode 32 X 16 characters, monochrome;
- Graphics mode: 256 X 208;
- Sound: 3 - channels + white noise provided by AY-3-8910;
- I / O ports: two 8 - bit parallel ports (e.g. printer and general port).

site project:
http://www.spetsialist-mx.ru/Galaksija/index6.html
GALAKSIJA PLUS
*Wpsload community is a sharing platform. We are not responsible for any design issues and parameter issues (board thickness, surface finish, etc.) you choose.
Attribution-ShareAlike (CC BY-SA) License
Read More⇒
Raspberry Pi 5 7 Inch Touch Screen IPS 1024x600 HD LCD HDMI-compatible Display for RPI 4B 3B+ OPI 5 AIDA64 PC Secondary Screen(Without Speaker)
BUY NOW- Comments(0)
- Likes(3)
-
Bernardo Silva
Apr 24,2026
-
Emil Klin?arski
Oct 29,2025
-
astrodoggie
Jul 12,2023
- 0 USER VOTES
- YOUR VOTE 0.00 0.00
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
More by Alexiev
-
usb midi interface
This is a replacement board for the cheap chineese USB to MIDI converter for fixing all issues with ...
-
short for Si5351A Pico Breakout Board
The Si5351APicoBoB (short for Si5351A Pico Breakout Board) is a specialized version of the clock gen...
-
Si5351A Breakout Board
This project is a specialized breakout board for the Si5351A clock generator chip, designed by Jason...
-
Low Pass Filter (LPF) module v1
This is a high-performance Low Pass Filter (LPF) module designed specifically for amateur radio appl...
-
Low Pass Filter (LPF) module v2
This is a high-performance Low Pass Filter (LPF) module designed specifically for amateur radio appl...
-
FY6900 OCXO
10 Mhz OCXO for FY6900 signal generator using Vectron C4550A1-0213 , U74HC14L that acts as Schmitt-t...
-
Afterburner - GAL chip programmer for Arduino
This is a GAL IC programmer software that allows to program GAL IC chips from various manfucaturers....
-
ATFBlast - ATF16V8, GAL16V8, ATF22V10 and GAL22V10 chips programmer
ATF16V8, GAL16V8, ATF22V10 and GAL22V10 chips programmer.This is custom PCB variant of ATFBlast proj...
-
ArduTrx Attenuator or Dummy load
IntroductionTo test the ArduTrx or transceivers in general a dummy load is a handy device (https://e...
-
ArduTrx Open Source Hamradio Transceiver for Arduino
The ArdTrx project consists of two parts: the ArduTrx shield and the software. Both parts can be use...
-
MonochromeVGA
MonochromeVGA is a product to enjoy the charm of those monochrome monitors of the time but in the cu...
-
NES64 Make Your Own Joystick
The NES64 is a replacement PCB for use in an existing controller for the Nintendo Entertainment Syst...
-
AY-3-8912 Emulator (AVR-AY)
AY-3-8912 Emulator (AVR-AY)used in many old computers as Amstrad CPC, Oric-1, Colour Genie, Elektor ...
-
4116 dram tester
project by : Muttley Black
-
Covox Speech Thing Sound Card SMD version
he Covox Speech Thing is an external audio device attached to the computer to output digital sound. ...
-
Covox Speech Thing Sound Card for Parallel Port LPT with resistor DAC - Short version
Covox Speech Thing Sound Card for Parallel Port LPT with resistor DAC - Short verionThe short versio...
-
Covox Speech Thing Sound Card for Parallel Port LPT with resistor DAC - Long version
Instead of using two types of resistors with 1/2 relation, I just used all the same types, but doub...
-
8bit ISA IBM XT, 286, 386, 486 Analog input card - Game control adapter
Recreation of IBM Analog input card 99.1 mm* 79.4 mmAn 8-bit ISA card with gameport. It avoids the...
-
-
ARPS-2 – Arduino-Compatible Robot Project Shield for Arduino UNO
2531 0 5 -
-
A Compact Charging Breakout Board For Waveshare ESP32-C3
2984 3 8 -
AI-driven LoRa & LLM-enabled Kiosk & Food Delivery System
3192 2 1 -
-
-
-
ESP32-C3 BLE Keyboard - Battery Powered with USB-C Charging
3259 0 2 -







